Top 5 Ways to Fix Unable to Contact Your DHCP Server Error on Windows 10

Jazuli T Barconi

The Dynamic Host Configuration Protocol (DHCP) server is a network protocol that automatically assigns IP addresses. It also distributes the network configuration to all connected devices, such as the DNS server, subnet mask, and default gateway. But often, an error can appear when renewing, releasing, or leasing an IP address. If you receive unable to contact your DHCP server error on Windows 10, try these fixes.



Fix Unable to Contact Your DHCP Server Error on Windows 10

A DHCP server allows for network configuration of newly connected devices without setting up static individual IP addresses. Instead, the process is automated with the DHCP server and network interface controller often communicating to refresh and release the addresses.

Unfortunately, a lack of communication between the protocols can interrupt internet access. If you can no longer surf the internet due to the inability to contact your DHCP server error, here are some solutions.

1. Register Your DNS

At times, initiating a manual dynamic registration for the DNS name and IP address can fix the error. You can do this by registering your DNS using a command prompt.

Step 1: Type cmd on the Windows search bar, and the right-hand side, select Run as administrator.



Cmd command

Step 2: Type this command and press Enter

ipconfig /registerdns


Command prompt ipconfig registerdns

Step 3: Restart your computer and confirm if the error is resolved. If not, try the other fixes.

2. Restart Your DHCP Server

The error can occur if the DHCP has stopped or your system can’t connect to the service. To resolve this, restart your DHCP client service.

Step 1: Press Windows + R keys, type services.msc in the run dialog box and press Enter.



Run services msc

Step 2: Locate the DHCP client option, right-click on it, and select Properties.



Windows services DHCP client

Step 3: Stop the Services status.

Step 4: Set the Startup type to Automatic.

Step 5: Click the Start button, click OK, then Apply to update the changes.



DHCP client running services

3. Reset TCP/IP

Resetting Winsock and IP stack is another workable solution to the error. To reset TCP/IP follow these steps.

Step 1: Type and click cmd on Windows search bar and Run as administrator.



Cmd command

Step 2: Type the following commands and press Enter after each one.

netsh winsock reset
netsh int ip reset
ipconfig /release
ipconfig /renew
ipconfig /flushdns

Step 3: Restart your computer and see if the error has cleared.

4. Update and Reinstall Network Drivers

Old and outdated drivers are a common cause for the unable to contact your DHCP server error. Updating your system will release newer versions that support your network protocol. Reinstalling the network drivers helps recognize the right drivers for your device.

Step 1: Right-click on the Windows Start button and select Device manager.



Device Manager Windows 10

Step 2: Locate Network adapters and expand the list. Select the problematic network adapter and click Update driver.



Device manager network adapters

Step 3: Tap Search automatically for updated driver software. And once the process is complete, restart your PC.



Device manager update drivers search automatically

Alternatively, uninstall then reinstall the problematic driver. Here’s how you can do it.

Step 1: On the Network adapters option, select Uninstall device.



Device manager uninstall network adapter driver

Step 2: Confirm the process by tapping the Uninstall option.



Device manager confirm uninstall

Step 3: At the top of the screen, click Scan for hardware changes.



Device manager scan for hardware changes

Wait for Windows to complete the process, then restart your device.

To add to this, consider rolling back to a version that previously worked for your computer. Here’s how you can do it.

Step 1: Navigate to the problematic network adapter, right-click on it and select Properties.

Step 2: Select the Driver tab and locate the Roll Back Driver option and click on it. Press OK.

Note: If the option is greyed out, there isn’t a backup file since the driver wasn’t updated recently.



Device manager roll back driver

5. Turn Off IPv6

The error also occurs if the IPv6 is enabled and there isn’t a local network to connect to. To fix this issue, disable IPv6.

Step 1: Press Windows + R keys to open the Run dialog box.

Step 2: Type ncpa.cpl in the search box, then press Enter.



Run ncpa cpl

Step 3: Locate the internet connection you are using and right-click on it. Next, tap Properties.



Network connections properties

Step 4: On the Networking tab, uncheck the Internet Protocol version 6 (IPv6) option and click OK to update the changes.



Network connections I Pv6

Restart your computer and confirm if the error appears.

Browse Seamlessly

A DHCP server that works right saves time and money. It ensures a continuous flow of activities with new and old devices dynamically being assigned IP addresses. Every unique IP address assigned to a device, ensures seamless browsing with uninterrupted connections and better productivity.



The above article may contain affiliate links which help support Guiding Tech. However, it does not affect our editorial integrity. The content remains unbiased and authentic.

Next Post

WiFi Adapter not working on Windows 11/10 computer

If you notice you’re having network & internet connection problems on your Windows 10 or Windows 11 PC and issues like Unidentified network appearing, the Wi-Fi connection is limited, low Wi-Fi signal strength or the WiFi adapter is not working at all, then this post is intended to help you with […]
judi bola Slot kamboja mudah menang dengan pilihan beberapa server slot thailand deposit pulsa serta via dana 24 jam nonstop, kunjungi segera agencuan untuk dapatkan promosi new member dengan bebeas ip to terkecil 2023. Slot Thailand pragmatic play idn poker idn poker slot online akun pro thailand idn poker